![]() Once you click on the Manage Dongle License button, you will be asked to type your license key for verification purpose. option from the Mitti menu, and click on the Manage Dongle License button. To make a Dongle, your computer has to have a Mitti 2 perpetual license installed, and needs to be online. The USB drive needs to have a unique serial number, and it should use APFS file system - prerequisite to use APFS file system is to use GUID partition table. When you plug it into a computer it makes Mitti 2 registered - until you unplug it. In Mitti 2, you can transfer seats of a perpetual license to a USB thumb drive of your choice, to create a USB Dongle. If your computer has been broken and stolen, the License Account page offers a limited number of Emergency Deactivations that renews yearly. Once you re-activated your copy, you can properly deactivate it. If you forgot to deactivate your copy but wiped out the hard drive, you will be still able to re-activate your license key on that computer again and it won't count as a new activation, since Activations are computer-dependent. panel that you can find in the Mitti menu. ![]() The Deactivate Online command is available from the Registration. The computer needs to be connected to the internet - just like with activation. you want to move your license to a new computer - you should deactivate it. If you no longer need your license on a computer - e.g. If you need to increase the allowed number of computers with your license, you can purchase more seats in your License Account page. You can list the computers associated with your license as well as the basic license info on your License Account page. Use your e-mail address associated with your license to login. You must see 000X where X is the current version of the MITT firmware.You can retrieve your license key on your FastSpring Order Account Page. Notice the seven segment on the MITT board. The preceding output shows a successful installation of the second MITT firmware image. The second chip's firmware cannot be updated until the first chip is installed. Run MuttUtil.exe –UpdateFirmware again for the second chip, after the first firmware update is complete. The preceding output shows a successful installation of the first firmware image. The firmware is updated only if MuttUtil has newer firmware. ![]() MuttUtil compares the version of the firmware on the board with the firmware version contained within MuttUtil. If you are using the FPGA development board, the EEPROM can take up to 5 minutes to program. There are two separate chips that require firmware on the MITT board. The preceding output shows that the WinUSB loaded as the device driver for the board. In a command prompt from Program Files\MITT\, run this command: Ignore the warning about the driver might be compatible with the hardware. Under Model select USB MUTT DEFAULT from the list and click Next.Ĭlick Yes and install the driver. on the Select the device driver you want to install for this hardware page.īrowse to the MITT installation directory (Program Files\MITT\ or Program Files (x86)\MITT\ ) in the Install From Disk dialog and click Ok. Select Show All Devices and click Next in the Select your device's type from the list below page.Ĭlick on Have Disk. Select Let me pick from a list of device drivers on my computer. Select Browse my computer for driver software in the Update Driver Software dialog. Right-click on the node and choose Update Driver Software. In Device Manager, locate the device node. Make sure that the board power switch (next to the audio jack) is turned on. We recommend that you use root hub ports and avoid controllers with embedded hubs. Install MITT firmwareĬonnect the MITT board to a USB 2.0 port on the host computer. For more information, see Debugging Tools for Windows (WinDbg, KD, CDB, NTSD) and Windows Debugging. Debugging tools are installed with the WDK. The system under test must be connected to a kernel debugger. The runtime is installed here %ProgramFiles(x86)%\Windows Kits\8.1\Testing\Runtimes\TAEF For complete installation instructions, follow the steps described in WDTF Runtime Library.ĭownload location: WDK and WinDbg downloads When you install the Windows Driver Kit (WDK), the runtime is installed automatically. To run the MITT tests, you need Windows Driver Test Framework (WDTF). If your SUT is a phone, then the host computer, SUT, and MITT board must be configured as shown in this image.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |